Vintage wilton vise parts. Old Wilton Vise Identification? What You Should Know 2019-12-15

Wilton Tradesman Vises: Quality American Craftsmanship

Vintage wilton vise parts

If you have a few hours, and want to read a lot more on the topic of Wilton vise date stamps, check out this thread over on the Garage Journal Forum. Removal I have had several that were really stuck, and making a Jack Screw is a great starting point. Using a dial caliper works too. Customers ask how to cut serrations in the jaw faces. Take your time and check often with a set of calipers or a micrometer. If ever you received one without a stamp, this just goes to show that it was either released accidentally, or they were made early even before Wilton added the slide key.

Next

What's the deal with Wilton vises?

Vintage wilton vise parts

Most of the vises have smaller models which were most likely not sold to many. Some have no stamp at all, and some have been known to have typos with dates that are almost certainly wrong. The Tradesman has all the features and performance that made Wilton famous. The idea is to get the dirt and grime off the vise while providing some lubrication and thin film to prevent future rust. The spindle handle threads, top of the swivel base, and front jaw sleeve the part that inserts into the back jaw got a a slightly heavier coating. It's also a good idea to have a small container handy for small parts to keep them from getting lost. I decided to build a fixture.

Next

Wilton Base Assembly and Used Vise Parts

Vintage wilton vise parts

Where Else to Learn About Old Wilton Vises You can begin the thread in this blog in the comment section right below. For large vises wire wheeling may be your only viable option. Rotating head switches between a woodworkers vise with dog, to a machinist bench vise with pipe jaws. If you are a collector and 50% or more of the original paint is present, my opinion is to not restore it. Brass and Silver Solder works too. I have an abrasive blast cabinet filled with crushed glass which allows me to clean and prep the surface of the vise for paint.

Next

Restoration of Wilton Bullet Vise: 6 Steps (with Pictures)

Vintage wilton vise parts

I like using high-strength 1144 carbon steel from McMaster Carr. The stuff did not even get patented until then. Each knob is drilled and reamed for a precision hole and the fixture is machined and threaded for a flat head cap screw. The 7 inch Prentiss I show in my top picture will most likely have to be drilled out and removed with a slide hammer. .

Next

Restoration of Wilton Bullet Vise: 6 Steps (with Pictures)

Vintage wilton vise parts

When attaching the new tire on a band saw wheel, it may appear too be too small, however it really is not. I lightly coated all vise surfaces that rub against any other vise surfaces. This is because castings would sit unused for years at a time, so vises could have date stamps that were made long after the vise was cast! That's why it's fortunate many people publish in forums to give light to various queries on the topic. I have had a few that were tight and I had to remove them by welding a slide hammer to the pin and pulling them out like the welded ones. Get a 5 gallon bucket and soak for 24-48 hours. Mine shot about 30 feet when it came loose, but it wasn't damaged. The knob is bolted tight and then easily worked into shape.

Next

Wilton Bullet Vise Parts

Vintage wilton vise parts

The picture shows a ratchet spindle off a Prentiss that is pretty worn on the sides. And that's how you find out the fate from your old Wilton vise identification! There are a couple ways of doing it. Heat is a good way to clean the crack. Going from a budget vise to a Tradesman is like trading your Ford Escort in for a Porsche. This makes the process of learning about your scout vise manufacturing date even more difficult.

Next

Wilton Vise Parts

Vintage wilton vise parts

. I know how difficult it must be looking for more information regarding the old Wilton vise identification. The three horseshoe washer screws were replaced by three new 10:32 socket head stainless screws from the local hardware store. This was my third vise restoration, but the first of this design. Add the screw and tighten it as tight as you dare. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers.

Next

Vintage Vises

Vintage wilton vise parts

Here is how I fit the Collars I make and sell on my website. It is easy to leave out critical details on the phone or in emails, which kills a lot of time on both ends. If you want, you can remove the center post with pliers for safe keeping. Before you start this step, have some old rags handy. After carefully looking at the geometry created taken with the microscope, it became clear the teeth were rotated at 14 degrees and the teeth are cut at 90 degrees.

Next

Wilton Vise Date Stamping • MIVise

Vintage wilton vise parts

His prices are very fair. Also show a broken screw but hat was fairly easy to pull out. On each Collar listing I add a machinist drawing and on the listing description I list this dimension as the width. Restoration Step 1 - Disassembly You are taking the plunge, congratulations! If you are collecting vises and enjoy the restoration process it's probably worth restoring but if you simply want the vise to use on your workbench, simply wipe it down with some penetrating oil and enjoy using that vintage tool. As can be seen, it is stamped with 4-53. Wipe off any excess lubricant. I wouldn't bother with a swivel base plate.

Next

Vintage and Collectible Vises and Clamps

Vintage wilton vise parts

With wide, reversible main jaws, replaceable pipe jaws, a 360 degree swivel base, and a nice sized work anvil, the Tradesman is up to a wide range of tasks. Dont waste my time or your. Bench vise handles get abused almost as much as the jaws. This gives a un even wear or rub of the Spindle when opening the vise. . Others will look like 6-30-60, which would be June 30, 1960.

Next